Hydraulic Trolley Jack, 2-Ton Capacity

Cric Rouleur Hydraulique, Capacité de 2 Tonnes

Hydraulischer Hebelroller, 2 Tonnen Kapazität

Cric Idraulico a Carrello, Capacità 2 Tonnellate

Gato Hidráulico de Botella, Capacidad 2 Toneladas

Hydraulische Autokrik, Capaciteit 2 Ton

油圧トローリージャッキ、容量2トンB07XFSSFDS

English � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3

Français � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 16

Deutsch � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 29

Italiano � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 42

Español � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 55

Nederlands � � � � � � � � � � � � � � � � � � � � � � � � � � � � 68

日本語 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 81

3

EN

IMPORTANT SAFEGUARDSRead these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.

When using the product, basic safety precautions should always be followed to reduce the risk of injury including the following:

DANGER Risk of death! Never work on, around, or under a load supported only by the product. Use a pair of adequately rated jack stands.

DANGER Risk of death! Support the vehicle with appropriate means, immediately after lifting.

DANGER Risk of death! Lift only on areas of the vehicle as specified by the vehicle manufacturer.

CAUTION Risk of injury! Wear appropriate personal protective equipment (PPE) as required by applicable to local regulations.

• The owner and/or operator shall have an understanding of the product, its operating characteristics, and safety operating instructions before operating the product. Safety information shall be understood. If the operator is not fluent in English, the product and safety instructions shall be discussed with the operator in the operator’s native language by the purchaser, owner, or owner’s designee, making sure that the operator comprehends their contents.

• Study, understand, and follow all instructions before operating this product.

• Visual inspection shall be made before each use of the product by checking for abnormal conditions, such as cracked welds, leaks, and damaged, loose, or missing parts.

• Other inspections shall be made per product operating instructions.

• The product shall be inspected immediately if the product is believed to have been subject to an abnormal load or shock. This inspection should be made by a manufacturer’s or supplier’s authorized repair facility.

• Owners and operators should be aware that repair of this equipment may require specialized knowledge and facilities.

• Any product that appears to be damaged in any way, is found to be worn, or operates abnormally SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. Necessary repairs should be made by manufacturer’s or supplier’s authorized repair facility.

4

EN

• The product shall be maintained by a qualified person.

• Do not exceed rated capacity.

• Use only on a hard, level surface.

• Ensure load is secured to the product.

• No alterations shall be made to this product.

• Only attachments and/or adapters supplied by or approved by the manufacturer shall be used.

• Release load-locking devices (if employed) slowly and carefully.

• Center load on saddle (lift pad) prior to lifting.

• Do not move or dolly the vehicle while it is on the jack.

• Before using the product with the vehicle, always engage the vehicle parking brakes and block the wheels.

SAVE THESE INSTRUCTIONSIntended Use• This product is designed to lift (not support), rated capacity loads

consisting of one end of a vehicle. Immediately after lifting, the load must be supported by a pair of appropriately rated jack stands. Wood blocks, bricks, or concrete blocks are not acceptable substitutes for jack stands.

• This product is intended for private use only. It is not intended for commercial use in garages or repair shops.

• This product is intended to be used in dry indoor and outdoor areas.

• No liability will be accepted for damages resulting from improper use or non-compliance with these instructions.

5

EN

Do not:

• Use on three wheel cars, trailers, mobile homes (caravans), RVs and campers.

• Use on curved or tubular vehicles.

• Use in extreme climates, freezer application or in strong magnetic fields.

• Use in potentially explosive atmospheres or in mines.

• Use for lifiting of persons.

• Handle loads which could lead to dangerous situations (e.g molten metal, acids, radiating materials, especially brittle loads).

Product Description

A

B

C E

G

I

D

FH

A Actuating handle (base) F Lift arm (lifting beam)

B Actuating handle receptacle G Saddle (lift pad)

C Cover plate H Actuating handle (extension)

D Oil plug I Release valve

E Carrying handle

6

EN

Before First Use• Check the product for transport damages.

• Remove all the packing materials.

• Perform air purging procedure as described in the “Purging Air from Hydraulic System” section.

DANGER Risk of suffocation! Keep any packaging materials away from children – these materials are a potential source of danger, e.g. suffocation.

AssemblyStep 1:

H A

Step 2:

C

B

7

EN

Step 3:

E

Purging Air from Hydraulic SystemNOTICE Air bubbles may become trapped occasionally inside

the hydraulic system, reducing its efficiency. Purge the air following the directions below.

NOTICE Oil can leak from the release valve (I) whilst purging air. Have a rag ready in case of any leakages.

• Without any weight on the jack, open the release valve (I) by making one full turn in a counter-clockwise direction.

• Remove the cover plate (C) to expose the oil plug (D).

• Pump the handle rapidly with 8 full strokes to push the air through the system.

• Use a flat screwdriver and slightly push the oil plug (D) to the side to purge trapped air.

• Securely close the release valve (I) in a clockwise direction.

• Refit the cover plate (C).

• Check for proper pump and lift action. Repeat the above steps until the air is fully purged.

8

EN

Inspection• Visual inspection shall be made before each use of the product by

checking for abnormal conditions, such as cracked welds, leaks, and damaged, loose, or missing parts.

• The product shall be inspected immediately if the product is believed to have been subject to an abnormal load or shock. This inspection should be made by a manufacturer’s or supplier’s authorized repair facility.

• Inspect the work area as well. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

OperationLifting up the vehicle

DANGER Risk of death! Never work on, around, or under a load supported only by the product. Use a pair of adequately rated jack stands.

• Engage the vehicle brake and block the wheels for better lift stability.

• Place the product at a 90º angle to the vehicle under the vehicle’s lift point. Position the product so the saddle (lift pad) (G) is centered and will contact the lift point firmly.

• Consult the vehicle’s owner manual if you are in doubt about the location of the lift points.

• Ensure the product is at a 90º angle to the vehicle and under the specified points for lifting.

• Close the release valve (I) by rotating it in a clockwise direction.

• Pump the handle until the saddle (lift pad) (G) is in close proximity to the lift point.

• Continue pumping until the vehicle is lifted to the desired height.

• Remove the actuating handle (A and H) from the handle receptacle (B).

• After lifting, support the load with appropriately rated jack stands (not provided).

9

EN

NOTICE Operator must keep eyes on the product and load at all times during operation.

NOTICE If several jacks are used together, raise the vehicle on both sides with the same speed. Keep the same height on both sides.

NOTICE Always ensure that the load is stabilized or supported in such a way that it will not shift during lifting or lowering procedure.

NOTICE Never wire, clamp or otherwise disable the release valve (I) function. Use the handle (A) to ensure proper release valve (I) operation.

Lowering the vehicle DANGER Risk of death! Ensure there are no objects or persons

under the vehicle before lowering the vehicle.

• Pump the handle to raise the vehicle from the jack stand(s).

• Remove the jack stand(s).

• Use the handle (A) to slowly turn the release valve (I) in a counter-clockwise direction to lower the vehicle onto the ground.

WARNING Risk of death or injury! Use extreme caution when lowering the jack. Opening the release valve (I) too fast can cause the jack to lower rapidly.

WARNING Risk of death or injury! If the product should malfunction at any time, secure the load with jack stands and refer to the Troubleshooting section.

SpecificationsMaximum loading capacity: approx. 4409 lbs (2000 kg)

Lifting height:min. 5.31" (135 mm)max. 13.4" (340 mm)

Net weight: approx. 19.2 lbs (8.7 kg)

Dimensions (W x H x D):approx. 17.6 x 7.72 x 5.3" (447 x 196 x 135 mm)

Product life time: 2 years

10

EN

Troubleshooting

Causes and solutions

The product does not lift load

The product does not hold load

The product does not lower

Completely close the release valve (I).

X X

Weight capacity exceeded.

X

Purge air from system.

X

Add oil. X X

Drain excessive oil.Lubricate moving parts.

X

Jack is binding or foreign obstruction.

X

Causes and solutions

Poor jack liftingThe product does not lift to full extension

Completely close the release valve (I).

X

Weight capacity exceeded.

Purge air from system.

X

Add oil. X X

Drain excessive oil.Lubricate moving parts.

Jack is binding or foreign obstruction.

X

11

EN

Cleaning and MaintenanceCleaning

• To clean the product, wipe with a soft, slightly moist cloth.

• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

Adding oil

• Place the product in an upright position.

• Turn the release valve (I) in a counter-clockwise direction to allow the saddle (G) to fully retract. Use force if necessary.

• Remove the cover plate (C) and then the oil plug (D).

• Fill the Hydraulic Jack Oil up to the lower rim of the fill hole. Keep dirt and other material clear when pouring. Do not overfill.

• Refit the oil plug (D) and then the cover plate (C).

Changing/draining oil CAUTION Take special care when handling hydraulic oil. Eye &

skin irritant. If contact with eyes occurs, flush thoroughly with water for 15 minutes while lifting eyelids and get prompt medical attention.

NOTICE For best performance replace the hydraulic oil at least once per year.

• Place the product in an upright position.

• Turn the release valve (I) in a counter-clockwise direction to allow the saddle (G) to fully retract. Use force if necessary.

• Remove the cover plate (C) and then the oil plug (D).

• Turn the product upside down and drain the fluid into a certified oil container.

• Refit the oil plug (D) and then the cover plate (C).

LubricatingNOTICE Risk of malfunction! Never lubricate or grease the rods of

the pump and lifting cylinder.

• For light duty use, regularly lubricate for all external moving parts once a month.

• For heavy duty and frequent use, lubricate once a week.

• Use only SAE10 grade, special-purpose hydraulic oil (not provided). Dispose of all used and spilled oil.

12

EN

Other maintenance

• Regularly check and maintain the oil level.

• Check the ram every 3 months for any rust or corrosion. Clean as needed and wipe with an oil cloth.

• Keep the rating label clean and readable at all time. Stop using the product if label is not readable or if it is detached.

• Necessary repairs or modification should be made by manufacturer’s or supplier’s authorized repair facility.

Oil disposal

• Dispose of hydraulic oil, residue and the empty container in accordance with all local, state and federal laws and regulations. It is illegal to dump waste oil into landfill or waterways. Disposing of used hydraulic oil the incorrect manner has the potential to pollute the environment.

Storage

• Always store the product in the fully lowered position.

• If the product is stored outdoors, lubricate all parts before and after use to ensure the product stays in good working condition.

• For long term storage drain the hydraulic oil.

Feedback and HelpLove it? Hate it? Let us know with a customer review.

AmazonBasics is committed to delivering customer-driven products that live up to your high standards. We encourage you to write a review sharing your experiences with the product.

US: amazon.com/review/review‑your‑purchases#

UK: amazon.co.uk/review/review‑your‑purchases#

US: amazon.com/gp/help/customer/contact‑us

UK: amazon.co.uk/gp/help/customer/contact‑us

13

EN

Exploded View

41

4039

3837363534333231302928

42

2

316

1718

1718

191817202122

15

279

2623

2425 14

1312

1110

87

6

1

45

14

EN

No. Part Description Quantity

1 QLQD2A.1-1 Handle cover 1

2 T820033.1(asm) Actuating handle 1

3 T820050-1 Cover plate 1

4 Locating pin 1

5 Positioning spring 1

6 Supporting shaft 1

7 Pin for frame 1

8 Supporting shaft 1

9 Connecting rod 2

10 Lift arm assembly 1

11 GB894.1-16 C-clip Ø16 mm 2

12 GB91-2X20 Cotter pin Ø2 x 20 mm 1

13 T82000Y.3-1 Saddle 1

14 QLQD2C.5-2a Saddle pin 1

15 GB894.1-10 C-clip Ø10 mm 4

16 Right frame assembly 1

17 Spring washer M12 6

18 GB6170-M12 Nut M12 6

19 Carrying handle 1

20 GB97.1-12 Washer M12 2

21 T820013-7 Sleeve for front wheel 2

22 T820013D-2 Front wheel 2

23 Saddle base assembly 1

24 Pin for saddle base 1

25 GB894.1-13 C-clip Ø13 mm 1

26 Shaft for front wheel 1

15

EN

No. Part Description Quantity

27 Pin for lift arm 1

28 T820033XE.2(asm) Rear caster assembly 2

29 Left frame assembly 1

30 Return spring 1

31 TF1201C-29 Oil plug 1

32 T820050.1 Power unit assembly 1

33 GB308-6 Steel ball bearing Ø6 mm 1

34 T83003.2-10(asm) Release value assembly 1

35 QLQD2A.2-5(asm) Pump plunger assembly 1

36 QLQD2A.2-7b U-Bracket for plunger 1

37 T820050.1-2 Handle receptacle 1

38 QLQD2B-3Roundwire snap ring Ø1.4 x 26 mm

1

39 QLQD2A.2-19 Pin for pump plunger 1

40 QLQD2A.2-20 Pin for unit base 1

41 QLQD2B.2-5Roundwire snap ring Ø1.2 x 20 mm

1

42 T820050.MF Seal kit 1

amazon.com/AmazonBasics

V01-12/19

MADE IN CHINA

FABRIQUÉ EN CHINE

HERGESTELLT IN CHINA

PRODOTTO IN CINA

HECHO EN CHINA

GEMAAKT IN CHINA

中国製