instruction no. 1home.agh.edu.pl/.../2014_ue_lab/2016/lab1_eng_2016.pdf · c) one test for whole...
TRANSCRIPT
Instruction no. 1
Introduction to laboratory and MULTISIM
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.1
ELECTRONIC CIRCUITS
Lecture:
prof. dr hab. inż. Wojciech Kucewicz
Laboratory:
mgr inż. Piotr Dorosz (C2/409) [email protected]
Department of Electronics, AGH-UST,
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.2
Classes 90 minutes a week
From the beginning of electronics (Ohm’s law, Kirchhoff’s rule)
Through electronics devices (semiconductor, diode, bipolar transistor,
unipolar transistor)
Ending with integrated circuits used in practical applications
(automotive in particular).
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.3
How the final grade is determined (from laboratory):
1. Points acquired during lab (60% of the final grade - 20 points max):
a) Successfully following and completing instructions 1-6 (6x1 point) – 6 points
b) 3 miniprojects from instructions 7-9 (5+4+5 points) – 14 points
2. Test (40% of the final grade – 40 points max)
a) Twice a semester
b) Regarding topics appearing during laboratories
c) One test for whole Mechatronics. There is no lab in „test” week.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.4
𝐹𝑖𝑛𝑎𝑙 𝑔𝑟𝑎𝑑𝑒 % = 𝐿𝐴𝐵
20× 100% × 0.6 +
𝑇𝐸𝑆𝑇
40× 100% × 0.4
Electronics deals with electrical circuits that involve active electrical
components such as vacuum tubes, transistors, diodes and integrated
circuits, and associated passive interconnection technologies. The
nonlinear behaviour of active components and their ability to control
electron flows makes amplification of weak signals possible and
electronics is widely used in information processing,
telecommunications, and signal processing. The ability of electronic
devices to act as switches makes digital information processing possible.
Interconnection technologies such as circuit boards, electronics
packaging technology, and other varied forms of communication
infrastructure complete circuit functionality and transform the mixed
components into a regular working system.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.5
General distinction:
-analog electronic circuits
-digital electronic circuits.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.6
Analogue electronics (or analog in American English) are electronic
systems with a continuously variable signal, in contrast to digital
electronics where signals usually take only two different levels. The term
"analogue" describes the proportional relationship between a signal and a
voltage or current that represents the signal. The word analogue is
derived from the Greek word ανάλογος (analogos) meaning
"proportional„
Digital electronics, or digital (electronic) circuits, represent signals by
discrete bands of analog levels, rather than by a continuous range. All
levels within a band represent the same signal state. Relatively small
changes to the analog signal levels due to manufacturing tolerance,
signal attenuation or parasitic noise do not leave the discrete envelope,
and as a result are ignored by signal state sensing circuitry.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.7
An analog or analogue signal is any continuous signal for which the
time varying feature (variable) of the signal is a representation of some
other time varying quantity, i.e., analogous to another time varying
signal. An analog signal has a theoretically infinite resolution.
Digital electronics, or digital (electronic) circuits, represent signals by
discrete bands of analog levels, rather than by a continuous range. All
levels within a band represent the same signal state. In most cases the
number of these states is two, and they are represented by two voltage
bands: one near a reference value (typically termed as "ground" or zero
volts) and a value near the supply voltage, corresponding to the "false"
("0") and "true" ("1") values of the Boolean domain respectively.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.8
Basic Electrical Quantities:
-current,
-voltage,
-electrical resistance,
-capacity.
Basic Passive Elements:
-resistor,
-capacitor,
-potentiometer.
Basic Electronics Laws:
-Ohm’s law,
-Kirchhoff’s law.
They are the key issues in understanding what is going on during these classes!!!
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.9
Electric current intensity- I (called electric current), it is a physical
quantity characterizing the flow of current. It is defined as the ratio
between the electric load vaule flowing through defined surface and the
time of the flow:
Ampere – electric current intensity unit. It is the base unit in both SI and
MKSA systems of unit, marked with A symbol.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.10
Electric voltage– difference of electric potentials between two points of
an electric circuit or electric field. The symbol of voltage is U. Voltage is
equal to the work done per unit charge against a static electric field to
move the charge between two points.
The volt (symbol: V) is the SI derived unit for electric potential
(voltage), electric potential difference, and electromotive force. A single
volt is defined as the difference in electric potential across a wire when
an electric current of one ampere dissipates one watt of power.
Additionally, it is the potential difference between two points that will
impart one joule of energy per coulomb of charge that passes through it.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.11
Electrical resistance (R symbol) – a quantity characterizing the relations
between voltage and electric current intensity in the circuits of direct
current (DC). In alternating current (AC) circuits electrical resistance is
the real part of complex impedance. The unit of resistance in SI is an
Ohm (Ω).
U=RI
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.12
Electrical capacitance of the secluded conductor is a physical quantity
C equal to the ratio between load q accumulated on the conductor and the
electrical potential of that conductor.
1 Farad (F) – the unit of electrical capacitance in SI (SI derived unit)
This is the capacitance of the electrical conductor, the potential of which
is increased by 1 volt after 1 Coulomb load delivery.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.13
A resistor is a passive two-terminal electrical component that
implements electrical resistance as a circuit element. The ratio of the
voltage applied across a resistor's terminals to the intensity of current in
the circuit is called its resistance, and this can be assumed to be a
constant (independent of the voltage) for ordinary resistors working
within their ratings. It is a linear element i.e. voltage drop over it is
proportional to the current flowing through it. Practical resistors have a
series inductance and a small parallel capacitance.
Capacitor is an electrical element built with two conductors (electrodes)
separated by dielectric. Voltage supplied to the capacitor electrodes
causes the assembly of the electric charge. After disconnecting the power
supply, load remains on the electrodes because of the electrostatic forces.
If the capacitor as a whole is not electrified then the charge accumulated
on both covers is equal in value but of opposite sign. The capacitor has a
capacitance C determining the ability of the capacitor to accumulate the
charge.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.14
A potentiometer, informally a pot, is a three-terminal resistor with a
sliding contact that forms an adjustable voltage divider. If only two
terminals are used, one end and the wiper, it acts as a variable resistor or
rheostat.
A potentiometer measuring instrument is essentially a voltage divider
used for measuring electric potential (voltage); the component is an
implementation of the same principle, hence its name.
Potentiometers are commonly used to control electrical devices such as
volume controls on audio equipment. Potentiometers operated by a
mechanism can be used as position transducers, for example, in a
joystick. Potentiometers are rarely used to directly control significant
power (more than a watt), since the power dissipated in the
potentiometer would be comparable to the power in the controlled load.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.15
Ohm’s Law
Georg Simon Ohm was a German physicist and mathematician. He
discovered the relationship in 1825-1826.
Ohm's law states that the current through a conductor between two points
is directly proportional to the potential difference across the two points.
I
UR
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.16
Design Tool
MULTISIM: electronic circuits simulator.
It allows to:
Check how the circuit built from virtual elements works, without the need of physically creating the circuit itself.
Free version of the program can be downloaded from: http://www.ni.com/multisim/
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.17
źródła
podstawowe
elementy
diody
tranzystory
układy analogowe
układy cyfrowe
Toolbar-elements of electronic and electrical systems AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.18
Measurement devices
and analyzers menu
przyrząd pomiarowy
generator
oscyloskop
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.19
„Checking” OHM’S LAW using MULTISIM
Stage 1- „placing” voltage
controlled voltage source.
1. Wybierz
źródła
2. Wybierz
źródło
napięcia
sterowane
napięciem
3. Połóż
element
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.20
The result
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.21
Stage 2. „placing” voltage source
Result
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.22
Placing potentiometer (regulated resistor)
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.23
Placing multimeter
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.24
Build the circuit!!!
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.25
Start the simulation
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.26
Current measurement (click twice on multimeter 1
with LMB – Left Mouse Button)
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.27
Voltage measurement on the resistance AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.28
Changing the voltage on voltage source in
the circuit with the test 1kOhm resistor – click
twice LMB AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.29
Setting the potentiometer on 40%, the results of voltage and current
measured (U to I ratio stays constant!!!) AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.30
Check voltage and current for different settings of the potentiometer
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.31
Function generator: electronic device used for generating electrical
signals of different shape:
-sinusoidal,
-rectangle,
-triangle.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.32
Setting the generator
(LMB click twice)
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.33
Oscilloscope - is a type of electronic test instrument that allows
observation of constantly varying electrical signals, usually as a two-
dimensional graph.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.34
Oscilloscope – settings
(LMB click twice)
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.35
Connecting the devices
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.36
Simulation – functional generator connected to the oscilloscope
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.37
A light-emitting diode (LED) is a semiconductor
light source. Appearing as practical electronic
components in 1962, early LEDs emitted low-intensity
red light, but modern versions are available across the
visible, ultraviolet, and infrared wavelengths, with
very high brightness.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.38
Build the circuit
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.39
Run the simulation AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.40
Setting the frequency of the generator enables to change the period of
częstotliwości generatora pozwala na zmianę okresu of lighting and
extinguishing the LED.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.41
Coming up next
week!!!
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.42
Kirchhoff’s Laws
Kirchhoff's first law – At any node (junction) in an electrical circuit, the
sum of currents flowing into that node is equal to the sum of currents
flowing out of that node, or:
The algebraic sum of currents in a network of conductors meeting at a
point is zero.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.43
Kirchhoff's second law– also called voltage law, applies to the balance
of voltage in the closed circuit.
In the closed circuit voltage drops on the total resistance is the sum of
electromotive forces present in the circuit.
AGH • Zespół Mikroelektroniki • Electronic Circuits • P. Dorosz Lab 1.44